UK flood barrier supplier since 2012 Sole UK distributor of Water-Gate

Photography to follow

Safeguard

Drybase Tanking Slurry 25kg

  • Cement-based waterproof coating for basements, cellars and below-ground walls
  • BBA certified (18/5549) as Type A waterproofing to BS 8102
  • Works on the wet side or the inside of the wall
  • Brush, trowel or spray onto concrete, brick, block or stone
  • Approved by the Drinking Water Inspectorate for contact with drinking water
  • 25kg bag, mix with water on site
Coming soon

Want to know when it's available? Get in touch

  • UK-wide delivery, including the Highlands, islands and Northern Ireland, and to the Isle of Man. Contact us for the Channel Islands and export. See delivery charges
  • UK stock and UK-wide delivery
  • Supply only, or supplied and installed
  • Trade and public-sector accounts welcome

Need product information or a data sheet? Call 0115 987 0358.

Overview

Built for the job.

Drybase Tanking Slurry is a ready-mixed powder of cement, graded quartz sand and additives. Mixed with water and brushed or sprayed onto a wall or floor, it bonds to the surface and forms a hard waterproof layer that holds back water while still letting vapour through.

It is used to waterproof basements, cellars, foundations, retaining walls, lift pits, tanks and pools, on new and existing buildings. It can go on the side facing the water or on the inside face, so it suits converting an existing cellar where you cannot dig out the outside of the wall.

The BBA certifies it as fully bonded Type A waterproofing to BS 8102, for Grades 1 to 3 (Grade 3 needs environmental control too), with resistance to water pressure up to a 6m head. It is also approved by the Drinking Water Inspectorate for contact with drinking water, and once applied should last the life of the structure.

Preparing the surface

  • The surface must be sound, open-pored and rough. Remove paint, bitumen, oil and laitance
  • Cut out cracks wider than 0.3mm to at least 20mm deep and repair with Drybase Universal Mortar
  • Stop active leaks with Drybase Waterproof Plug
  • Dampen the surface before applying, but do not leave it wet
  • On weak brick or block, apply a 10mm 3:1 sand:cement render first and leave for 24 hours

How to apply

  • Mix 25kg of powder with 4.5 to 6 litres of clean water using a mechanical mixer for at least 3 minutes. Use within about 45 minutes.
  • Apply the first coat with a masonry brush, trowel or spray. Maximum 4kg/m² per coat.
  • Apply the second coat while the first is still damp.
  • Keep the coating damp for at least 5 days. Protect from rain for 24 hours and from frost for 5 days.
  • Do not use heating, air conditioning or dehumidifiers for 28 days. Backfill after 3 days. Wait 4 weeks before painting.

Do not apply below 5°C or onto frozen surfaces. Drybase Tanking Slurry does not accommodate structural movement and floors need a screed over it. Finish internal walls with a compatible plaster such as Dryzone renovation plaster, not gypsum.

Safety

Contains cement. Wear gloves, eye protection and a dust mask when mixing. Read the safety data sheet before use.

Specification

Full spec sheet.

Product typeCementitious tanking slurry (cement, graded quartz sand, additives)
Pack size25kg bag
ColourGrey
CertificationBBA 18/5549; BS 8102 Type A, Grades 1 to 3; Drinking Water Inspectorate approved; EN 1504-3
Water pressureUp to 6m head (BBA)
Coverage (no water pressure)3 to 4kg/m², 1.5 to 2mm total. About 6 to 8m² per bag
Coverage (water under pressure)4 to 6kg/m², 2 to 3mm total. About 4 to 6m² per bag
CoatsUsually 2. Maximum 4kg/m² per coat
Mixing water4.5 to 6 litres per 25kg
Pot lifeAbout 45 minutes at 20°C
Set timeAbout 5 to 8 hours at 20°C
Compressive strengthClass R3 (25MPa or more)
Vapour permeableYes
Reaction to fireA1
ApplicationBrush, trowel or spray
Minimum temperature5°C
Shelf life12 months unopened
StorageDry, 5°C to 35°C, protect from frost
SKU / barcodeTK-DRYBASESLURRY25KG / 5060132763797
ManufacturerSafeguard Europe Ltd, UK

Bag coverage figures are worked out from Safeguard's kg/m² rates.

Questions

Common questions.

How many bags do I need?

Where there is no water pressure, allow one bag per 6 to 8m². Where water is under pressure, allow one bag per 4 to 6m².

Can I apply it on the inside of a basement wall?

Yes. It works against water pressure from either side, so it can be applied internally.

How many coats do I need?

Usually two, with the second applied while the first is still damp.

Can I plaster over it?

Yes, with a compatible plaster such as Dryzone renovation plaster. Do not use gypsum plaster.

Is it suitable for water tanks?

Yes. It is approved by the Drinking Water Inspectorate for contact with drinking water.

Who we have worked with

Trusted by the organisations that manage Britain's water.

Get in touch

Talk to the team.

Send us a message and we will come back to you. If you are after a price for a specific opening, use the quote form instead so we get the dimensions with your enquiry.

We use these details to reply to your enquiry. See our Privacy Policy (opens in a new tab).

Contact us Contact us